Safety
How do I disinfect correctly, and what is disinfectant contact time?
Clean first, then use an EPA-registered disinfectant exactly as its label says, especially the contact time: how long the surface must stay wet for the product to work. Wiping it off early means it may not have worked. Most routine house cleaning only needs cleaning; disinfect when someone is sick or at higher risk.
Why it happens
Disinfectants are regulated by EPA as antimicrobial pesticides. The label's directions, surfaces and contact time are the conditions under which the product works. Dirt can block disinfectants from reaching germs, and spray-and-wipe skips the contact time.
EPA-registered disinfectant, used exactly as labeled
No reviews yet. Tried it? Be the first.
What you need
- EPA-registered disinfectant (look for the EPA Reg. No. on the label)
- Soap or detergent and water for pre-cleaning
- Gloves
Tips
- In the List N tool, enter only the first two parts of the registration number (for 12345-12-2567, enter 12345-12).
Steps
- Find the EPA registration number on the product and check it on EPA's List N tool or EPA's label database.
- Read the directions: check the use sites and surface types, and read the precautionary statements.
- Wash the surface with soap and water first if it's visibly dirty or the label calls for pre-cleaning.
- Apply the disinfectant and keep the surface wet for the full contact time on the label.
- Wear gloves. Throw away disposable gloves after each cleaning; wash your hands after removing gloves.
- Keep lids tightly closed and store products out of reach of children.
Where this comes from (3)
Diluted household bleach (when the label doesn't give directions)
No reviews yet. Tried it? Be the first.
What you need
- Regular unscented household bleach with 5% to 9% sodium hypochlorite
- Room-temperature water
- Labeled container
- Gloves and eye protection as the label directs
Steps
- Follow the bleach bottle's disinfecting directions if it has them.
- If it doesn't, use regular unscented household bleach (5% to 9% sodium hypochlorite), not laundry or splashless bleach.
- Mix 5 tablespoons (1/3 cup) bleach per gallon of room-temperature water, or 4 teaspoons per quart. Label the container.
- Clean visibly dirty surfaces with soap or detergent first.
- Apply and leave the surface wet for at least 1 minute, unless the manufacturer says otherwise.
- Make a fresh solution every day; it loses effectiveness after 24 hours.
Where this comes from (4)
- Cleaning and Disinfecting with Bleach (opens in a new tab) CDC
- Dangers of Mixing Bleach with Cleaners (opens in a new tab) Washington State Department of Health
- How to Clean Stainless Steel (opens in a new tab) GE Appliances
- Cleaning Hard Surfaces (opens in a new tab) American Cleaning Institute
Just clean, when disinfecting isn't needed
No reviews yet. Tried it? Be the first.
What you need
- Soap or detergent and water
Steps
- For routine housekeeping, clean with soap or detergent and water. CDC says regular cleaning is enough for most situations at home.
- Disinfect when someone in the home is sick or at higher risk of illness (for example, someone with a weakened immune system).
- When you do need a product, choose the least hazardous one that will do the job.
Where this comes from (2)
Choose a lower-hazard, DfE-certified disinfectant
No reviews yet. Tried it? Be the first.
What you need
- Disinfectant with EPA's Design for the Environment (DfE) logo
Steps
- When a disinfectant is needed, look for EPA's DfE logo or check EPA's list of DfE-certified disinfectants. The logo means the registered product also meets extra criteria for human health and environmental effects.
- Use it exactly as labeled, including the contact time.
Where this comes from (1)
Know a better way?
Suggest a solution we haven't listed. We check every suggestion against a trusted source before adding it.