Bathrooms
How do I clean dirty or stained grout?
For routine cleaning, use a neutral tile-and-grout cleaner and a soft brush. Mildew-stained grout is often treated with a dilute bleach solution or a mildew stain remover, though one grout maker advises against bleach. Badly neglected ceramic or porcelain tile can be restored with an acidic tile cleaner, then sealed.
Why it happens
Cement grout is porous, so it soaks up soil, soap residue and moisture, and mildew can grow on it. Strong acids, bleach and ammonia can wear down grout and its sealer over time, which is why routine cleaning should be gentle and stronger products saved for occasional deep cleans.
Neutral tile-and-grout cleaner with a soft brush
No reviews yet. Tried it? Be the first.
What you need
- Neutral (pH-balanced) cleaner made for ceramic and porcelain tile and grout
- Soft-bristle brush
- Mop or cloth and clean water
- Dry cloth
Steps
- Sweep or vacuum floor tile first to remove grit.
- Dilute the neutral cleaner as its label directs.
- Scrub the grout lines with a soft-bristle brush.
- Rinse thoroughly and buff the tile dry with a cloth.
Where this comes from (2)
- Sealing Ceramic and Porcelain Tile & Grout (care and maintenance) (opens in a new tab) LATICRETE
- Cleaning Hard Surfaces (opens in a new tab) American Cleaning Institute
Dilute bleach solution or mildew stain remover (mildew-stained grout)
No reviews yet. Tried it? Be the first.
What you need
- Liquid household bleach (3/4 cup per 1 gallon of water), OR a mildew stain remover
- Brush
- Gloves and eye protection
- Clean water for rinsing
Steps
- Open windows or doors and run the fan. Put on gloves and eye protection.
- Test in an out-of-the-way spot first.
- Mix 3/4 cup liquid household bleach into 1 gallon of water, or use a mildew stain remover as its label directs.
- Apply to the grout with a brush.
- Rinse thoroughly with water.
Where this comes from (4)
- Cleaning Hard Surfaces (opens in a new tab) American Cleaning Institute
- Sealing Ceramic and Porcelain Tile & Grout (care and maintenance) (opens in a new tab) LATICRETE
- Dangers of Mixing Bleach with Cleaners (opens in a new tab) Washington State Department of Health
- Cleaning and Disinfecting with Bleach (opens in a new tab) CDC
Acidic tile-and-grout restoration cleaner (heavy soap scum or hard-water film)
No reviews yet. Tried it? Be the first.
What you need
- Acidic cleaner made for ceramic and porcelain tile
- Alkaline tile cleaner (only if the floor is greasy)
- Brush, clean water, gloves and eye protection
Steps
- Use only for occasional restoration of ceramic or porcelain tile, not for routine cleaning.
- If the tile has heavy grease or oil, pre-clean with an alkaline cleaner made for ceramic and porcelain tile.
- Apply the acidic cleaner following its label for dilution and dwell time.
- Scrub, rinse thoroughly and let dry.
Where this comes from (3)
- Sealing Ceramic and Porcelain Tile & Grout (care and maintenance) (opens in a new tab) LATICRETE
- Learn About Cleaning Products for Natural Stone (opens in a new tab) Natural Stone Institute
- Dangers of Mixing Bleach with Cleaners (opens in a new tab) Washington State Department of Health
Seal the grout after a deep clean
No reviews yet. Tried it? Be the first.
What you need
- Impregnating (penetrating) grout sealer
Steps
- Let the grout dry completely after cleaning.
- Apply an impregnating grout sealer as its label directs. LATICRETE says fluorochemical-based sealers are best for grout.
- Afterwards, wipe up acidic spills (coffee, wine, juice, vinegar, tomato) promptly. Sealer helps against stains but cannot prevent acid etching.
Where this comes from (1)
Know a better way?
Suggest a solution we haven't listed. We check every suggestion against a trusted source before adding it.