Bathrooms
How do I get mold or mildew off shower caulk?
Scrub small areas with detergent and water, or use a bleach solution of no more than 1 cup bleach per gallon of water. If the stain is in the caulk and won't come out, cut the old caulk out, clean and dry the joint, and recaulk. Fix the moisture problem or the mold will come back.
Why it happens
Mold grows where moisture stays. The caulk joint around a tub or shower stays damp, and stains can sit in the caulk itself, so surface cleaning doesn't always remove them. EPA warns against caulking or painting over mold; clean and dry the surface first.
Scrub with detergent and water
No reviews yet. Tried it? Be the first.
What you need
- Detergent and water
- Scrub brush or sponge
- Gloves (non-latex, vinyl, nitrile or rubber), goggles and an N95 respirator
Steps
- Put on gloves and goggles that fully protect the eyes. CDC recommends at least an N95 respirator for mold cleanup.
- Scrub the mold off with detergent and water.
- Dry the area completely.
Where this comes from (2)
Bleach solution (no more than 1 cup per gallon) or a mildew stain remover
No reviews yet. Tried it? Be the first.
What you need
- Household bleach and water, OR a mildew stain remover
- Brush or cloth
- Gloves, goggles and an N95 respirator
Tips
- If the stain doesn't come out, replace the caulk rather than repeating bleach treatments.
Steps
- Open windows or doors and run the fan.
- Put on gloves, goggles and an N95 respirator.
- Mix no more than 1 cup of household bleach into 1 gallon of water, or use a mildew stain remover as its label directs.
- Apply to the caulk with a brush or cloth.
- Rinse and dry the area completely.
Where this comes from (3)
- Mold Clean Up Guidelines and Recommendations (opens in a new tab) CDC
- Cleaning Hard Surfaces (opens in a new tab) American Cleaning Institute
- Dangers of Mixing Bleach with Cleaners (opens in a new tab) Washington State Department of Health
Cut out and replace the caulk
No reviews yet. Tried it? Be the first.
What you need
- Utility knife or caulk-removal tool
- Caulk remover
- Isopropyl (rubbing) alcohol and a rag
- New caulk and caulk gun
- Painter's tape (optional)
Tips
- Remove all of the old caulk. Different caulk types won't stick to each other.
Steps
- Cut out the old caulk with a utility knife or caulk-removal tool, taking care not to damage the tub or tile.
- Apply caulk remover to soften what's left, then peel or scrape it away.
- Clean any remaining mold from the joint with detergent and water and let it dry completely. EPA says not to caulk over moldy surfaces.
- Wipe the joint with isopropyl alcohol, keeping water out of the open seam.
- Run painter's tape along both sides of the joint if you want clean edges.
- Apply new caulk in small sections and smooth it before it starts to dry (Do it Best notes about 10 minutes). Pull the tape before the caulk dries.
- Follow the caulk label for cure time before the shower is used.
Where this comes from (3)
- How to Remove and Replace Your Tub and Shower Caulk (opens in a new tab) Do it Best
- Mold Cleanup in Your Home (opens in a new tab) U.S. EPA
- Hazard Alert: Dangerous Chemical Combinations - Do Not Mix (opens in a new tab) New Jersey Department of Health
Fix the moisture (prevention)
No reviews yet. Tried it? Be the first.
What you need
- Squeegee or towel
Tips
- EPA: if you clean up mold but don't fix the water problem, the mold will most likely come back.
Steps
- Report leaks to the client so they can be fixed, and dry wet areas promptly.
- Leave shower doors ajar and enclosures open after use so air can circulate.
- Wipe walls with a towel or squeegee after each shower.
Where this comes from (2)
- Mold Cleanup in Your Home (opens in a new tab) U.S. EPA
- Cleaning Hard Surfaces (opens in a new tab) American Cleaning Institute
Know a better way?
Suggest a solution we haven't listed. We check every suggestion against a trusted source before adding it.